The Microchip SERCOM-G1 UART driver (drivers/serial/uart_mchp_sercom_g1.c), used by the PIC32CM-JH SoC family, contains an out-of-bounds write in its asynchronous (DMA) receive path. When uart_rx_enable() is invoked with a one-byte receive buffer (len == 1) and CONFIG_UART_MCHP_ASYNC is enabled, the RX-complete ISR starts a single-beat DMA transfer while a received byte is already pending in the SERCOM DATA register. On this SoC the peripheral-triggered DMA start sequencing then writes one byte past the end of the caller-supplied buffer (CWE-787). The overflowed byte's value is the UART RX data supplied by the connected serial peer (adjacent attacker), while its size and location are fixed at one byte immediately after the buffer. Exploitation requires the async UART config (not enabled by default on the in-tree PIC32CM-JH boards) and a consumer that enables RX with a one-byte buffer; impact is limited single-byte memory corruption adjacent to the RX buffer (possible crash / denial of service). The defect shipped in v4.4.0. The fix reads the first byte with the CPU and, for one-byte buffers, performs no DMA at all; for larger buffers it sizes the DMA for the remaining len-1 bytes.
Review the upstream advisory, identify the affected product in your inventory, and apply the vendor update when one is available.
CVE-2026-10644 is listed in the HOL Guard supply-chain feed, but affected software is not mapped to a package. Review the upstream advisory for the affected product and vendor guidance. The Microchip SERCOM-G1 UART driver (drivers/serial/uart_mchp_sercom_g1.c), used by the PIC32CM-JH SoC family, contains an out-of-bounds write in its asynchronous (DMA) receive path. When uart_rx_enable() is invoked with a one-byte receive buffer (len == 1) and CONFIG_UART_MCHP_ASYNC is enabled, the RX-complete ISR starts a single-beat DMA transfer while a received byte is already pending in the SERCOM DATA register. On this SoC the peripheral-triggered DMA start sequencing then writes one byte past the end of the caller-supplied buffer (CWE-787). The overflowed byte's value is the UART RX data supplied by the connected serial peer (adjacent attacker), while its size and location are fixed at one byte immediately after the buffer. Exploitation requires the async UART config (not enabled by default on the in-tree PIC32CM-JH boards) and a consumer that enables RX with a one-byte buffer; impact is limited single-byte memory corruption adjacent to the RX buffer (possible crash / denial of service). The defect shipped in v4.4.0. The fix reads the first byte with the CPU and, for one-byte buffers, performs no DMA at all; for larger buffers it sizes the DMA for the remaining len-1 bytes.
Affected software not mapped. Review the upstream record for vendor-specific product and version guidance.
The Microchip SERCOM-G1 UART driver (drivers/serial/uart_mchp_sercom_g1.c), used by the PIC32CM-JH SoC family, contains an out-of-bounds write in its asynchronous (DMA) receive path. When uart_rx_enable() is invoked with a one-byte receive buffer (len == 1) and CONFIG_UART_MCHP_ASYNC is enabled, the RX-complete ISR starts a single-beat DMA transfer while a received byte is already pending in the SERCOM DATA register. On this SoC the peripheral-triggered DMA start sequencing then writes one byte past the end of the caller-supplied buffer (CWE-787). The overflowed byte's value is the UART RX data supplied by the connected serial peer (adjacent attacker), while its size and location are fixed at one byte immediately after the buffer. Exploitation requires the async UART config (not enabled by default on the in-tree PIC32CM-JH boards) and a consumer that enables RX with a one-byte buffer; impact is limited single-byte memory corruption adjacent to the RX buffer (possible crash / denial of service). The defect shipped in v4.4.0. The fix reads the first byte with the CPU and, for one-byte buffers, performs no DMA at all; for larger buffers it sizes the DMA for the remaining len-1 bytes.
Review the upstream advisory, identify the affected product in your inventory, and apply the vendor update when one is available.
CVE-2026-10644 is listed in the HOL Guard supply-chain feed, but affected software is not mapped to a package. Review the upstream advisory for the affected product and vendor guidance. The Microchip SERCOM-G1 UART driver (drivers/serial/uart_mchp_sercom_g1.c), used by the PIC32CM-JH SoC family, contains an out-of-bounds write in its asynchronous (DMA) receive path. When uart_rx_enable() is invoked with a one-byte receive buffer (len == 1) and CONFIG_UART_MCHP_ASYNC is enabled, the RX-complete ISR starts a single-beat DMA transfer while a received byte is already pending in the SERCOM DATA register. On this SoC the peripheral-triggered DMA start sequencing then writes one byte past the end of the caller-supplied buffer (CWE-787). The overflowed byte's value is the UART RX data supplied by the connected serial peer (adjacent attacker), while its size and location are fixed at one byte immediately after the buffer. Exploitation requires the async UART config (not enabled by default on the in-tree PIC32CM-JH boards) and a consumer that enables RX with a one-byte buffer; impact is limited single-byte memory corruption adjacent to the RX buffer (possible crash / denial of service). The defect shipped in v4.4.0. The fix reads the first byte with the CPU and, for one-byte buffers, performs no DMA at all; for larger buffers it sizes the DMA for the remaining len-1 bytes.
Affected software not mapped. Review the upstream record for vendor-specific product and version guidance.
Reported by NVD (nvd).
HOL Guard can help your team monitor supply-chain activity while the upstream record is clarified.
Explore HOL GuardReported by NVD (nvd).
HOL Guard can help your team monitor supply-chain activity while the upstream record is clarified.
Explore HOL Guard