The Zephyr ADIN2111/ADIN1110 10BASE-T1S/T1L Ethernet driver (drivers/ethernet/eth_adin2111.c) reassembles received Ethernet frames in OPEN Alliance (OA) SPI mode by copying device-supplied 64-byte data chunks into a fixed static buffer ctx->buf of size CONFIG_ETH_ADIN2111_BUFFER_SIZE (default 1524 bytes). In eth_adin2111_oa_data_read(), each valid chunk was memcpy'd into ctx->buf[ctx->scur] and the write cursor scur advanced, with no check that scur + len stayed within the buffer. The number of chunks (up to 255, from the BUFSTS RCA field) and the per-chunk length are taken entirely from the frame data received off the wire; the cursor is only reset on a start-of-frame chunk. An attacker on the single-pair Ethernet segment can therefore send a frame whose reassembled size exceeds the configured buffer, causing the driver's RX offload thread to write attacker-controlled frame bytes past the end of the static buffer into adjacent driver/kernel memory (up to roughly 14.8 KB in the worst case). This is a remotely/adjacently reachable out-of-bounds write (CWE-787) that can corrupt memory and cause denial of service or potentially code execution. The defect was introduced when OA SPI support was added (commit 0ca8b0756b1) and shipped in releases v3.7.0 through v4.4.0. The fix adds a bounds check that drops the oversized frame and resets the cursor before the copy.
The Zephyr ADIN2111/ADIN1110 10BASE-T1S/T1L Ethernet driver (drivers/ethernet/eth_adin2111.c) reassembles received Ethernet frames in OPEN Alliance (OA) SPI mode by copying device-supplied 64-byte data chunks into a fixed static buffer ctx->buf of size CONFIG_ETH_ADIN2111_BUFFER_SIZE (default 1524 bytes). In eth_adin2111_oa_data_read(), each valid chunk was memcpy'd into ctx->buf[ctx->scur] and the write cursor scur advanced, with no check that scur + len stayed within the buffer. The number of chunks (up to 255, from the BUFSTS RCA field) and the per-chunk length are taken entirely from the frame data received off the wire; the cursor is only reset on a start-of-frame chunk. An attacker on the single-pair Ethernet segment can therefore send a frame whose reassembled size exceeds the configured buffer, causing the driver's RX offload thread to write attacker-controlled frame bytes past the end of the static buffer into adjacent driver/kernel memory (up to roughly 14.8 KB in the worst case). This is a remotely/adjacently reachable out-of-bounds write (CWE-787) that can corrupt memory and cause denial of service or potentially code execution. The defect was introduced when OA SPI support was added (commit 0ca8b0756b1) and shipped in releases v3.7.0 through v4.4.0. The fix adds a bounds check that drops the oversized frame and resets the cursor before the copy.
Review the upstream advisory, identify the affected product in your inventory, and apply the vendor update when one is available.
CVE-2026-10673 is listed in the HOL Guard supply-chain feed, but affected software is not mapped to a package. Review the upstream advisory for the affected product and vendor guidance. The Zephyr ADIN2111/ADIN1110 10BASE-T1S/T1L Ethernet driver (drivers/ethernet/eth_adin2111.c) reassembles received Ethernet frames in OPEN Alliance (OA) SPI mode by copying device-supplied 64-byte data chunks into a fixed static buffer ctx->buf of size CONFIG_ETH_ADIN2111_BUFFER_SIZE (default 1524 bytes). In eth_adin2111_oa_data_read(), each valid chunk was memcpy'd into ctx->buf[ctx->scur] and the write cursor scur advanced, with no check that scur + len stayed within the buffer. The number of chunks (up to 255, from the BUFSTS RCA field) and the per-chunk length are taken entirely from the frame data received off the wire; the cursor is only reset on a start-of-frame chunk. An attacker on the single-pair Ethernet segment can therefore send a frame whose reassembled size exceeds the configured buffer, causing the driver's RX offload thread to write attacker-controlled frame bytes past the end of the static buffer into adjacent driver/kernel memory (up to roughly 14.8 KB in the worst case). This is a remotely/adjacently reachable out-of-bounds write (CWE-787) that can corrupt memory and cause denial of service or potentially code execution. The defect was introduced when OA SPI support was added (commit 0ca8b0756b1) and shipped in releases v3.7.0 through v4.4.0. The fix adds a bounds check that drops the oversized frame and resets the cursor before the copy.
Affected software not mapped. Review the upstream record for vendor-specific product and version guidance.
Reported by NVD (nvd).
HOL Guard can help your team monitor supply-chain activity while the upstream record is clarified.
Explore HOL GuardReview the upstream advisory, identify the affected product in your inventory, and apply the vendor update when one is available.
CVE-2026-10673 is listed in the HOL Guard supply-chain feed, but affected software is not mapped to a package. Review the upstream advisory for the affected product and vendor guidance. The Zephyr ADIN2111/ADIN1110 10BASE-T1S/T1L Ethernet driver (drivers/ethernet/eth_adin2111.c) reassembles received Ethernet frames in OPEN Alliance (OA) SPI mode by copying device-supplied 64-byte data chunks into a fixed static buffer ctx->buf of size CONFIG_ETH_ADIN2111_BUFFER_SIZE (default 1524 bytes). In eth_adin2111_oa_data_read(), each valid chunk was memcpy'd into ctx->buf[ctx->scur] and the write cursor scur advanced, with no check that scur + len stayed within the buffer. The number of chunks (up to 255, from the BUFSTS RCA field) and the per-chunk length are taken entirely from the frame data received off the wire; the cursor is only reset on a start-of-frame chunk. An attacker on the single-pair Ethernet segment can therefore send a frame whose reassembled size exceeds the configured buffer, causing the driver's RX offload thread to write attacker-controlled frame bytes past the end of the static buffer into adjacent driver/kernel memory (up to roughly 14.8 KB in the worst case). This is a remotely/adjacently reachable out-of-bounds write (CWE-787) that can corrupt memory and cause denial of service or potentially code execution. The defect was introduced when OA SPI support was added (commit 0ca8b0756b1) and shipped in releases v3.7.0 through v4.4.0. The fix adds a bounds check that drops the oversized frame and resets the cursor before the copy.
Affected software not mapped. Review the upstream record for vendor-specific product and version guidance.
Reported by NVD (nvd).
HOL Guard can help your team monitor supply-chain activity while the upstream record is clarified.
Explore HOL Guard